Send us a text

By providing your phone number, you consent to receive transactional/informational text messages (SMS) from Anderson Roofing, powered by Topline Pro. You can unsubscribe at any time by replying STOP. Message and data rates may apply. Message frequency varies.

By submitting this form, you agree to our Terms of Service & Privacy Policy.

Standing seam metal roof with white flashing around a clad rooftop enclosure and a roofer in a hi-vis jacket working alongside

STEEL AND SHEET METAL

METAL METAL METAL

Metal Roofing in Portland, OR

Founded in 1952, Anderson Roofing installs steel roofing and sheet metal on commercial, industrial and institutional buildings, from facilities in Portland and Salem.

  • Since 1952
  • Oregon CCB #293
  • BBB Accredited, A+
  • 24/7 emergency service

The case for steel

Why a metal roof?

A metal roof gives a building longevity and resilience against harsh weather, and steel adds exceptional strength to that protection. In a wet climate like Portland's, that resilience is the point: the roof has to keep shedding water year after year. Its modern lines complement the architecture of commercial, industrial and institutional buildings, and the same profiles read well on residential architecture too.

The roof is only as good as the installation. Anderson Roofing installs metal as a roofing specialist, with attention to detail at every seam, flashing and termination, using top-grade materials designed to last for years without constant upkeep. Sheet metal is one of the systems Anderson's own expertise spans, so the panels and the metal that finishes them can come from one contractor, with fewer hand-offs and fewer places for a detail to be missed.

What steel brings

  • DurabilityBuilt to last for years, with very little upkeep once it is on.
  • StrengthExceptional strength from steel, panel after panel.
  • Weather resistanceShields the building against harsh weather.
  • Thermal insulationEfficient insulation alongside the weather protection.
  • AppearanceModern lines for commercial and residential architecture.

The profile

How a standing seam roof goes together

Read the roof in section, from the deck up. Each panel locks to its neighbour at a raised seam, and clips under the seam hold the panel down, so the surface that sheds water has no screws through it.

Standing seam profile, section view

Section drawing of a standing seam roof: panels with raised seams, held by clips that are fastened through the underlayment into the deck SEAM PANEL UNDERLAYMENT CLIP DECK

Schematic, not to scale. Panel profiles vary by project.

Seam
The raised joint where two panels lock together, standing above the flat where water runs.
Panel
The formed steel sheet that carries water down the slope between seams.
Clip
A concealed bracket fastened to the deck that holds the panel from underneath.
Underlayment
The water-resistant layer that sits between the deck and the panels.
Deck
The structural surface the roof is built on and the clips are fastened to.

Closed seam, detail

Detail of a closed standing seam: the outer fold of one panel locks over the inner hem of its neighbour, with the clip tab held between them 1 2 3
  1. Outer fold: one panel's leg turns over the top.
  2. Inner hem: the neighbouring panel's leg tucks inside.
  3. Clip tab: rises from the clip and sits between the legs.

Sheet metal work

The sheet metal that finishes the roof

Sheet metal is one of the systems Anderson Roofing works in, listed in the company's own scope beside hot asphalt, single-ply membranes, fluid-applied coatings, green roofing and shingles. On a metal roof it does the detail work.

  1. 01
    Metal panel roof across an industrial building, with ventilators and skylights set into the panel field

    Panel roofs

    Long runs of metal panel across a large building, with ventilators and skylights set into the roof.

  2. 02
    Green standing seam metal roof meeting a flat roof, with formed metal trim along the junction

    Flashings and copings

    Formed metal flashing and coping close the junction where a metal roof meets a low-slope roof.

  3. 03
    Brick chimney finished with new metal flashing and a formed metal cap

    Chimney caps and terminations

    Metal flashing and a formed cap seal the top of a brick chimney where it passes through the roof.

  4. 04
    Green standing seam metal roof planes with formed edge trim, above a city view

    Gutters and edge metal

    Gutters and edge metal carry water off the roof and finish the eave and rake lines.

See more finished work in the Metal Roofs gallery.

Long sloped roof run between two buildings, with a metal-clad wall along one edge
A long sloped run between two buildings, with metal wall cladding and edge metal along one side.

Fit by building

Where metal suits

  • Steep roof with raised seams

    Steep and visible roofs

    Steep slopes shed water quickly, and a roof that is seen from the street or from neighbouring buildings carries its metal profile as part of the architecture.

  • Long, low roof run with repeating seams

    Long-run, low-maintenance roofs

    Where the owner wants a roof that does not ask for constant upkeep, long panel runs, concealed clips and no exposed fasteners keep the maintenance list short.

  • Locked seam joining two panels

    Buildings where weight and seam security matter

    Metal panels weigh less per square foot than many other roof coverings, and locked seams keep the joints closed. For a building where roof load and seam security are on the checklist, that counts.

Have a building in mind? Ask for a free estimate on your metal roof.

Local record

Metal roofing from a Portland contractor since 1952

Anderson Roofing works from fully equipped facilities in Portland and Salem, on commercial, industrial and institutional roofs across Oregon and beyond. Crews average 10 years with the company, and foremen have 12 to 30 years in the field.

One of the best Commercial roofing company's in the North West.

Brian Record - Google - Sep 2017 A customer's words, posted as a Google review.

Areas served

  • Portland OR
  • Vancouver WA
  • Eugene OR
  • Salem OR
  • Gresham OR
  • Hillsboro OR
  • Beaverton OR
  • Bend OR
  • Springfield OR
  • Boise ID
  • San Jose CA
  • Seattle WA
  • Oregon CCB #293

    Active, Commercial General Contractor Level 1, first licensed in 1972. Check the Oregon CCB lookup.

    Oregon CCB record: no complaints, civil penalties, sanctions or administrative suspensions in the past 10 years.

  • Public Works Bonded

    Bonded for public work since 2006, which is what lets Anderson bid schools, campuses and public agencies.

  • Bonded and insured

    An $80,000 commercial surety bond and $1,000,000 in liability insurance, as shown on the Oregon CCB record.

  • BBB A+ rated

    BBB Accredited since 2019. Read the BBB profile.

  • 4.9 on Google

    A 4.9 average across 15 Google reviews.

  • Always reachable

    24/7 emergency service, with the office open Monday to Friday, 7:00am to 5:00pm.

Questions

Metal roofing questions

Straight answers about metal roofs for commercial, industrial and institutional buildings in Portland and the surrounding region.

How much does a metal roof cost in Portland?

The cost depends on the roof area, the slope, the panel profile and how much flashing and edge metal the building needs, so a fair figure needs a look at the actual roof. Anderson Roofing provides free estimates for all of its roofing services, and the estimate is built from your roof rather than a rule of thumb.

How is a standing seam metal roof installed?

Underlayment goes over the deck first. Clips are then fastened to the deck, the panels are set over them and locked together along their raised seams, so the weathering surface carries no exposed fasteners. Flashings, edge metal and terminations finish the roof at walls, curbs, chimneys and eaves, as the profile drawing above shows.

Does Anderson Roofing install metal roofs outside Portland?

Yes. Anderson Roofing works in Portland OR, Vancouver WA, Eugene OR, Salem OR, Gresham OR, Hillsboro OR, Beaverton OR, Bend OR, Springfield OR, Boise ID, San Jose CA and Seattle WA, with fully equipped facilities in Portland and Salem. Mention the building's address when you request a quote.

How long does a metal roof last, and what upkeep does it need?

A metal roof is designed to last for years without constant upkeep, which is the main reason owners choose steel. In practice its life depends on the panel material, the quality of the installation and the care taken at flashings and penetrations. Anderson Roofing also offers maintenance and roof inspections, so the roof can be checked on a schedule.

Planning a metal roof in Portland?

Tell Anderson Roofing about the building and the roof. Estimates are free, and 24/7 emergency service is available. The office is open Monday to Friday, 7:00am to 5:00pm.